ARM: dts: Add Pi Zero 2 support

Signed-off-by: Phil Elwell <phil@raspberrypi.com>

arch/arm/boot/dts/Makefile

@@ -7,6 +7,7 @@ dtb-$(CONFIG_ARCH_BCM2835) += \
 	bcm2708-rpi-cm.dtb \
 	bcm2708-rpi-zero.dtb \
 	bcm2708-rpi-zero-w.dtb \
+	bcm2710-rpi-zero-2.dtb \
 	bcm2709-rpi-2-b.dtb \
 	bcm2710-rpi-2-b.dtb \
 	bcm2710-rpi-3-b.dtb \

arch/arm/boot/dts/bcm2710-rpi-zero-2.dts

+/dts-v1/;
+
+#include "bcm2710.dtsi"
+#include "bcm2709-rpi.dtsi"
+#include "bcm283x-rpi-csi1-2lane.dtsi"
+#include "bcm283x-rpi-i2c0mux_0_44.dtsi"
+#include "bcm2708-rpi-bt.dtsi"
+#include "bcm283x-rpi-cam1-regulator.dtsi"
+
+/ {
+	compatible = "raspberrypi,model-zero-2", "brcm,bcm2837";
+	model = "Raspberry Pi Zero 2";
+
+	chosen {
+		bootargs = "coherent_pool=1M 8250.nr_uarts=1 snd_bcm2835.enable_compat_alsa=0 snd_bcm2835.enable_hdmi=1";
+	};
+
+	aliases {
+		serial0 = &uart1;
+		serial1 = &uart0;
+		mmc1 = &mmcnr;
+	};
+};
+
+&gpio {
+	spi0_pins: spi0_pins {
+		brcm,pins = <9 10 11>;
+		brcm,function = <4>; /* alt0 */
+	};
+
+	spi0_cs_pins: spi0_cs_pins {
+		brcm,pins = <8 7>;
+		brcm,function = <1>; /* output */
+	};
+
+	i2c0_pins: i2c0 {
+		brcm,pins = <0 1>;
+		brcm,function = <4>;
+	};
+
+	i2c1_pins: i2c1 {
+		brcm,pins = <2 3>;
+		brcm,function = <4>;
+	};
+
+	i2s_pins: i2s {
+		brcm,pins = <18 19 20 21>;
+		brcm,function = <4>; /* alt0 */
+	};
+
+	sdio_pins: sdio_pins {
+		brcm,pins =     <34 35 36 37 38 39>;
+		brcm,function = <7>; // alt3 = SD1
+		brcm,pull =     <0 2 2 2 2 2>;
+	};
+
+	bt_pins: bt_pins {
+		brcm,pins = <43>;
+		brcm,function = <4>; /* alt0:GPCLK2 */
+		brcm,pull = <0>;
+	};
+
+	uart0_pins: uart0_pins {
+		brcm,pins = <30 31 32 33>;
+		brcm,function = <7>; /* alt3=UART0 */
+		brcm,pull = <2 0 0 2>; /* up none none up */
+	};
+
+	uart1_pins: uart1_pins {
+		brcm,pins;
+		brcm,function;
+		brcm,pull;
+	};
+
+	audio_pins: audio_pins {
+		brcm,pins = <>;
+		brcm,function = <>;
+	};
+};
+
+&mmcnr {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdio_pins>;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins &bt_pins>;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>;
+	status = "okay";
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_pins &spi0_cs_pins>;
+	cs-gpios = <&gpio 8 1>, <&gpio 7 1>;
+
+	spidev0: spidev@0{
+		compatible = "spidev";
+		reg = <0>;	/* CE0 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <125000000>;
+	};
+
+	spidev1: spidev@1{
+		compatible = "spidev";
+		reg = <1>;	/* CE1 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <125000000>;
+	};
+};
+
+&i2c0if {
+	clock-frequency = <100000>;
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+	clock-frequency = <100000>;
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+};
+
+&i2s {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2s_pins>;
+};
+
+&leds {
+	act_led: led-act {
+		label = "led0";
+		linux,default-trigger = "actpwr";
+		gpios = <&gpio 29 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&hdmi {
+	hpd-gpios = <&gpio 28 GPIO_ACTIVE_LOW>;
+};
+
+&audio {
+	pinctrl-names = "default";
+	pinctrl-0 = <&audio_pins>;
+	brcm,disable-headphones = <1>;
+};
+
+&bt {
+	shutdown-gpios = <&gpio 42 GPIO_ACTIVE_HIGH>;
+};
+
+&minibt {
+	shutdown-gpios = <&gpio 42 GPIO_ACTIVE_HIGH>;
+};
+
+&cam1_reg {
+	gpio = <&gpio 40 GPIO_ACTIVE_HIGH>;
+};
+
+/ {
+	__overrides__ {
+		act_led_gpio = <&act_led>,"gpios:4";
+		act_led_activelow = <&act_led>,"gpios:8";
+		act_led_trigger = <&act_led>,"linux,default-trigger";
+	};
+};

arch/arm64/boot/dts/broadcom/Makefile

@@ -3,6 +3,7 @@ dtb-$(CONFIG_ARCH_BCM2835) += bcm2837-rpi-3-a-plus.dtb \
 			      bcm2837-rpi-3-b.dtb \
 			      bcm2837-rpi-3-b-plus.dtb \
 			      bcm2837-rpi-cm3-io3.dtb
+dtb-$(CONFIG_ARCH_BCM2835) += bcm2710-rpi-zero-2.dtb
 dtb-$(CONFIG_ARCH_BCM2835) += bcm2710-rpi-2-b.dtb
 dtb-$(CONFIG_ARCH_BCM2835) += bcm2710-rpi-3-b.dtb
 dtb-$(CONFIG_ARCH_BCM2835) += bcm2710-rpi-3-b-plus.dtb

arch/arm64/boot/dts/broadcom/bcm2710-rpi-zero-2.dts

+#include "../../../../arm/boot/dts/bcm2710-rpi-zero-2.dts"