Commit b352c596 authored by Theo Maillart's avatar Theo Maillart

Try to conf radius

parent e1d98dbc
......@@ -21,7 +21,7 @@ no shut
channel 36
end
! configure VLANs 82-83 via web interface
!!!!!!!!!!!!!! configure VLANs 82-83 via web interface
! ssid conf
conf t
......@@ -60,3 +60,17 @@ mbssid
int Dot11Radio0
mbssid
end
!!!Radius
conf t
aaa group server radius rad_eap
server 100.81.0.2 auth-port 1645 acct-port 1646
exit
aaa new-model
aaa authentication login eap_methods group rad_eap
radius-server host 100.81.0.2 auth-port 1645
acct-port 1646 key sr06
end
write memory
# -*- text -*-
##
## clients.conf -- client configuration directives
##
## $Id: 76b300d3c55f1c5c052289b76bf28ac3a370bbb2 $
#######################################################################
#
# Define RADIUS clients (usually a NAS, Access Point, etc.).
#
# Defines a RADIUS client.
#
# '127.0.0.1' is another name for 'localhost'. It is enabled by default,
# to allow testing of the server after an initial installation. If you
# are not going to be permitting RADIUS queries from localhost, we suggest
# that you delete, or comment out, this entry.
#
#
#
# Each client has a "short name" that is used to distinguish it from
# other clients.
#
# In version 1.x, the string after the word "client" was the IP
# address of the client. In 2.0, the IP address is configured via
# the "ipaddr" or "ipv6addr" fields. For compatibility, the 1.x
# format is still accepted.
#
client localhost {
# Only *one* of ipaddr, ipv4addr, ipv6addr may be specified for
# a client.
#
# ipaddr will accept IPv4 or IPv6 addresses with optional CIDR
# notation '/<mask>' to specify ranges.
#
# ipaddr will accept domain names e.g. example.org resolving
# them via DNS.
#
# If both A and AAAA records are found, A records will be
# used in preference to AAAA.
ipaddr = 127.0.0.1
# Same as ipaddr but allows v4 addresses only. Requires A
# record for domain names.
# ipv4addr = * # any. 127.0.0.1 == localhost
# Same as ipaddr but allows v6 addresses only. Requires AAAA
# record for domain names.
# ipv6addr = :: # any. ::1 == localhost
#
# A note on DNS: We STRONGLY recommend using IP addresses
# rather than host names. Using host names means that the
# server will do DNS lookups when it starts, making it
# dependent on DNS. i.e. If anything goes wrong with DNS,
# the server won't start!
#
# The server also looks up the IP address from DNS once, and
# only once, when it starts. If the DNS record is later
# updated, the server WILL NOT see that update.
#
#
# The transport protocol.
#
# If unspecified, defaults to "udp", which is the traditional
# RADIUS transport. It may also be "tcp", in which case the
# server will accept connections from this client ONLY over TCP.
#
proto = *
#
# The shared secret use to "encrypt" and "sign" packets between
# the NAS and FreeRADIUS. You MUST change this secret from the
# default, otherwise it's not a secret any more!
#
# The secret can be any string, up to 8k characters in length.
#
# Control codes can be entered vi octal encoding,
# e.g. "\101\102" == "AB"
# Quotation marks can be entered by escaping them,
# e.g. "foo\"bar"
#
# A note on security: The security of the RADIUS protocol
# depends COMPLETELY on this secret! We recommend using a
# shared secret that is composed of:
#
# upper case letters
# lower case letters
# numbers
#
# And is at LEAST 8 characters long, preferably 16 characters in
# length. The secret MUST be random, and should not be words,
# phrase, or anything else that is recognisable.
#
# The default secret below is only for testing, and should
# not be used in any real environment.
#
secret = testing123
#
# Old-style clients do not send a Message-Authenticator
# in an Access-Request. RFC 5080 suggests that all clients
# SHOULD include it in an Access-Request. The configuration
# item below allows the server to require it. If a client
# is required to include a Message-Authenticator and it does
# not, then the packet will be silently discarded.
#
# allowed values: yes, no
require_message_authenticator = no
#
# The short name is used as an alias for the fully qualified
# domain name, or the IP address.
#
# It is accepted for compatibility with 1.x, but it is no
# longer necessary in >= 2.0
#
# shortname = localhost
#
# the following three fields are optional, but may be used by
# checkrad.pl for simultaneous use checks
#
#
# The nas_type tells 'checkrad.pl' which NAS-specific method to
# use to query the NAS for simultaneous use.
#
# Permitted NAS types are:
#
# cisco
# computone
# livingston
# juniper
# max40xx
# multitech
# netserver
# pathras
# patton
# portslave
# tc
# usrhiper
# other # for all other types
#
nas_type = other # localhost isn't usually a NAS...
#
# The following two configurations are for future use.
# The 'naspasswd' file is currently used to store the NAS
# login name and password, which is used by checkrad.pl
# when querying the NAS for simultaneous use.
#
# login = !root
# password = someadminpas
#
# As of 2.0, clients can also be tied to a virtual server.
# This is done by setting the "virtual_server" configuration
# item, as in the example below.
#
# virtual_server = home1
#
# A pointer to the "home_server_pool" OR a "home_server"
# section that contains the CoA configuration for this
# client. For an example of a coa home server or pool,
# see raddb/sites-available/originate-coa
# coa_server = coa
#
# Response window for proxied packets. If non-zero,
# then the lower of (home, client) response_window
# will be used.
#
# i.e. it can be used to lower the response_window
# packets from one client to a home server. It cannot
# be used to raise the response_window.
#
# response_window = 10.0
#
# Connection limiting for clients using "proto = tcp".
#
# This section is ignored for clients sending UDP traffic
#
limit {
#
# Limit the number of simultaneous TCP connections from a client
#
# The default is 16.
# Setting this to 0 means "no limit"
max_connections = 16
# The per-socket "max_requests" option does not exist.
#
# The lifetime, in seconds, of a TCP connection. After
# this lifetime, the connection will be closed.
#
# Setting this to 0 means "forever".
lifetime = 0
#
# The idle timeout, in seconds, of a TCP connection.
# If no packets have been received over the connection for
# this time, the connection will be closed.
#
# Setting this to 0 means "no timeout".
#
# We STRONGLY RECOMMEND that you set an idle timeout.
#
idle_timeout = 30
}
}
# IPv6 Client
client localhost_ipv6 {
ipv6addr = ::1
secret = testing123
}
# All IPv6 Site-local clients
#client sitelocal_ipv6 {
# ipv6addr = fe80::/16
# secret = testing123
#}
#client example.org {
# ipaddr = radius.example.org
# secret = testing123
#}
#
# You can now specify one secret for a network of clients.
# When a client request comes in, the BEST match is chosen.
# i.e. The entry from the smallest possible network.
#
#client private-network-1 {
# ipaddr = 192.0.2.0/24
# secret = testing123-1
#}
#client private-network-2 {
# ipaddr = 198.51.100.0/24
# secret = testing123-2
#}
#######################################################################
#
# Per-socket client lists. The configuration entries are exactly
# the same as above, but they are nested inside of a section.
#
# You can have as many per-socket client lists as you have "listen"
# sections, or you can re-use a list among multiple "listen" sections.
#
# Un-comment this section, and edit a "listen" section to add:
# "clients = per_socket_clients". That IP address/port combination
# will then accept ONLY the clients listed in this section.
#
#clients per_socket_clients {
# client socket_client {
# ipaddr = 192.0.2.4
# secret = testing123
# }
#}
client 10.0.82.0/23 {
secret = sr06
shortname = borneWifi
}
#
# Configuration file for the rlm_files module.
# Please see rlm_files(5) manpage for more information.
#
# This file contains authentication security and configuration
# information for each user. Accounting requests are NOT processed
# through this file. Instead, see 'accounting', in this directory.
#
# The first field is the user's name and can be up to
# 253 characters in length. This is followed (on the same line) with
# the list of authentication requirements for that user. This can
# include password, comm server name, comm server port number, protocol
# type (perhaps set by the "hints" file), and huntgroup name (set by
# the "huntgroups" file).
#
# If you are not sure why a particular reply is being sent by the
# server, then run the server in debugging mode (radiusd -X), and
# you will see which entries in this file are matched.
#
# When an authentication request is received from the comm server,
# these values are tested. Only the first match is used unless the
# "Fall-Through" variable is set to "Yes".
#
# A special user named "DEFAULT" matches on all usernames.
# You can have several DEFAULT entries. All entries are processed
# in the order they appear in this file. The first entry that
# matches the login-request will stop processing unless you use
# the Fall-Through variable.
#
# Indented (with the tab character) lines following the first
# line indicate the configuration values to be passed back to
# the comm server to allow the initiation of a user session.
# This can include things like the PPP configuration values
# or the host to log the user onto.
#
# You can include another `users' file with `$INCLUDE users.other'
#
# For a list of RADIUS attributes, and links to their definitions,
# see: http://www.freeradius.org/rfc/attributes.html
#
# Entries below this point are examples included in the server for
# educational purposes. They may be deleted from the deployed
# configuration without impacting the operation of the server.
#
#
# Deny access for a specific user. Note that this entry MUST
# be before any other 'Auth-Type' attribute which results in the user
# being authenticated.
#
# Note that there is NO 'Fall-Through' attribute, so the user will not
# be given any additional resources.
#
#lameuser Auth-Type := Reject
# Reply-Message = "Your account has been disabled."
#
# Deny access for a group of users.
#
# Note that there is NO 'Fall-Through' attribute, so the user will not
# be given any additional resources.
#
#DEFAULT Group == "disabled", Auth-Type := Reject
# Reply-Message = "Your account has been disabled."
#
#
# This is a complete entry for "steve". Note that there is no Fall-Through
# entry so that no DEFAULT entry will be used, and the user will NOT
# get any attributes in addition to the ones listed here.
#
#steve Cleartext-Password := "testing"
# Service-Type = Framed-User,
# Framed-Protocol = PPP,
# Framed-IP-Address = 172.16.3.33,
# Framed-IP-Netmask = 255.255.255.0,
# Framed-Routing = Broadcast-Listen,
# Framed-Filter-Id = "std.ppp",
# Framed-MTU = 1500,
# Framed-Compression = Van-Jacobsen-TCP-IP
#
# The canonical testing user which is in most of the
# examples.
#
#bob Cleartext-Password := "hello"
# Reply-Message := "Hello, %{User-Name}"
#
#
# This is an entry for a user with a space in their name.
# Note the double quotes surrounding the name. If you have
# users with spaces in their names, you must also change
# the "filter_username" policy to allow spaces.
#
# See raddb/policy.d/filter, filter_username {} section.
#
#"John Doe" Cleartext-Password := "hello"
# Reply-Message = "Hello, %{User-Name}"
#
# Dial user back and telnet to the default host for that port
#
#Deg Cleartext-Password := "ge55ged"
# Service-Type = Callback-Login-User,
# Login-IP-Host = 0.0.0.0,
# Callback-Number = "9,5551212",
# Login-Service = Telnet,
# Login-TCP-Port = Telnet
#
# Another complete entry. After the user "dialbk" has logged in, the
# connection will be broken and the user will be dialed back after which
# he will get a connection to the host "timeshare1".
#
#dialbk Cleartext-Password := "callme"
# Service-Type = Callback-Login-User,
# Login-IP-Host = timeshare1,
# Login-Service = PortMaster,
# Callback-Number = "9,1-800-555-1212"
#
# user "swilson" will only get a static IP number if he logs in with
# a framed protocol on a terminal server in Alphen (see the huntgroups file).
#
# Note that by setting "Fall-Through", other attributes will be added from
# the following DEFAULT entries
#
#swilson Service-Type == Framed-User, Huntgroup-Name == "alphen"
# Framed-IP-Address = 192.0.2.65,
# Fall-Through = Yes
#
# If the user logs in as 'username.shell', then authenticate them
# using the default method, give them shell access, and stop processing
# the rest of the file.
#
#DEFAULT Suffix == ".shell"
# Service-Type = Login-User,
# Login-Service = Telnet,
# Login-IP-Host = your.shell.machine
#
# The rest of this file contains the several DEFAULT entries.
# DEFAULT entries match with all login names.
# Note that DEFAULT entries can also Fall-Through (see first entry).
# A name-value pair from a DEFAULT entry will _NEVER_ override
# an already existing name-value pair.
#
#
# Set up different IP address pools for the terminal servers.
# Note that the "+" behind the IP address means that this is the "base"
# IP address. The Port-Id (S0, S1 etc) will be added to it.
#
#DEFAULT Service-Type == Framed-User, Huntgroup-Name == "alphen"
# Framed-IP-Address = 192.0.2.32+,
# Fall-Through = Yes
#DEFAULT Service-Type == Framed-User, Huntgroup-Name == "delft"
# Framed-IP-Address = 198.51.100.32+,
# Fall-Through = Yes
#
# Sample defaults for all framed connections.
#
#DEFAULT Service-Type == Framed-User
# Framed-IP-Address = 255.255.255.254,
# Framed-MTU = 576,
# Service-Type = Framed-User,
# Fall-Through = Yes
#
# Default for PPP: dynamic IP address, PPP mode, VJ-compression.
# NOTE: we do not use Hint = "PPP", since PPP might also be auto-detected
# by the terminal server in which case there may not be a "P" suffix.
# The terminal server sends "Framed-Protocol = PPP" for auto PPP.
#
DEFAULT Framed-Protocol == PPP
Framed-Protocol = PPP,
Framed-Compression = Van-Jacobson-TCP-IP
#
# Default for CSLIP: dynamic IP address, SLIP mode, VJ-compression.
#
DEFAULT Hint == "CSLIP"
Framed-Protocol = SLIP,
Framed-Compression = Van-Jacobson-TCP-IP
#
# Default for SLIP: dynamic IP address, SLIP mode.
#
DEFAULT Hint == "SLIP"
Framed-Protocol = SLIP
#
# Last default: rlogin to our main server.
#
#DEFAULT
# Service-Type = Login-User,
# Login-Service = Rlogin,
# Login-IP-Host = shellbox.ispdomain.com
# #
# # Last default: shell on the local terminal server.
# #
# DEFAULT
# Service-Type = Administrative-User
# On no match, the user is denied access.
#########################################################
# You should add test accounts to the TOP of this file! #
# See the example user "bob" above. #
#########################################################
sr06 Cleartext-Password := "sr06"
Tunnel-Type = 13,
Tunnel-Medium-Type = 6,
Tunnel-Private-Group-Id = 2
radtest sr06 sr06 10.0.83.55 0 sr06
radtest sr06 sr06 localhost 0 testing123
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment